Lead

Approx. 250 / Kg Get Latest Price

Lead rod has been used in power supply equipment and clinical electrical stimulators. Lead Rod is also used as the starting material in lead bullets Lead tube is made from pure Lead Metal (99.97% min.) or Lead Alloys, which is readily fabricated by extrusion.Diameter: 12mm to 150mmGrade: 99%Shape: roundSize/Diameter: 12mm to 150mm

Approx. 250 / Piece Get Latest Price

This washer is in the shape of a ring cut by spring steel. Its ends are slightly raised up and down due to spring tension. These washers are placed above or below the nut or bolt and tighten so much that both their ends face each other and become leveled.

These washers are used to prevent a nut from loosening. These are used where there is vibration, or jolts occur. This puts pressure against the nut, preventing the latter (the nut) from turning and working loose.

There are several forms of spring washers. Each has its own advantages. Single pattern spring washer, standard pattern spring washer, double pattern spring washer, grip pattern spring washer, and girder pattern spring washer are the structures of spring washer.

Approx. 240 / Kg Get Latest Price

Body Lead or Body Soldering Sticks are a tin – lead alloy, which is composed to hold the “butter” consistency over a big temperature range while it is being spread.

INTRODUCTION TO BODY SOLDERING:

– First clean the area to be filled back to bare metal with a stripping disc, sanding paper etc.

– Brush solder paint over an area slightly larger than that to be filled and heat the area gently until you see the solder paint tin the panel.

– Remove excess solder paint with a clean cloth.

– Next, melt blobs of lead onto the panel over the area to be filled.

– Prepare your paddles by warming the surface of the tallow and wiping your paddle in the molten puddle. With a suitable amount of lead now deposited on the panel, heat it carefully until it can be spread like butter with your paddle.

– Control heat carefully and keep spreading until body solder is evenly spread over area.

– Wash with cool water to quench and to remove traces of acid solder paint.

Approx 0.5kg per stick. Also available pack of 10.

Approx. 250 / Kg Get Latest Price

In printing, type metal refers to the metal alloys used in traditional typefounding and hot metal typesetting. Historically, type metal was an alloy of lead, tin and antimony in different proportions depending on the application, be it individual character mechanical casting for hand setting, mechanical line casting or individual character mechanical typesetting and stereo plate casting. The proportions used are in the range: lead 50‒86%, antimony 11‒30% and tin 3‒20%. Antimony and tin are added to lead for durability while reducing the difference between the coefficients of expansion of the matrix and the alloy. Apart from durability, the general requirements for type-metal are that it should produce a true and sharp cast, and retain correct dimensions and form after cooling down. It should also be easy to cast, at reasonable low melting temperature, iron should not dissolve in the molten metal, and mould and nozzles should stay clean and easy to maintain. Today, Monotype machines can utilize a wide range of different alloys. Mechanical linecasting equipment uses alloys that are close to eutectic.

Approx. 250 / Kg Get Latest Price

Established in the Year 1988 in Mumbai, Maharashtra. We "Fine Metal India" are Partnership Firm, engaged as the foremost Wholesale Trader of Metal Ingots, Solder Stick & Solder Wire.

Approx. 250 / Kg Get Latest Price

Lead plate or sheet is a preferred solution for radiation shielding in many applications, including X-ray shielding, tank lining, acoustic shielding and nuclear shielding. We offer lead plate in almost any thickness and size. To request a quotation on an exact specification of lead sheet you require, please call us or send a email. Regardless of the specialized you are considering, we are available to offer appropriate options to meet your needs.

Lead Plate Specifications

We offer lead plate in thicknesses ranging from 1/64" up to 5".  

Lead Plate Weight Table

Approx. 250 / Kg Get Latest Price

American Elements' AE Bullion™ group mints certified high purity Lead Bars for short and long term physical possession and to allow for exposure and controlled risk to industrial demand fluctuations reflected in the global lead price. Besides lead bars, lead coins and lead ingots may be purchased by funds, currency reserves, exchange-traded funds (ETFs), private investors, collectors and hobbyists to take direct physical title and possession of the metal with risk exposure from shortages or chemical/physical technology changes, such as in solar energy, and fuel cell developments, equivalent to movements in the industrial application price of Lead. American Elements offers bonded short and long term warehouse inventory services for AE Bullion™ coins to investors, funds and collectors who do not wish to take physical custody of the metal or lack secure storage or warehouse capabilities. The lowest possible bar unit price to Lead melt value ratio is maintained through state of the art mint and die systems and analytically certified blanks (planchet or flan) refinedand pressed to exacting purity and weight. We also produce Lead as rod, pellets, powder, pieces, disc, granules, and wire, as nanoparticles and in compound forms, such as oxide. Lead Bars may be purchased in bulk or small quantity. Portfolios of different elemental metal bars or coins may also be structured and purchased from the AE Bullion™ group allowing for strategic risk allocation and indexing across a basket of metals.

Approx. 300 / Kg Get Latest Price

American Elements specializes in producing Lead High Purity Foil in many thicknesses and sizes for numerous industrial uses and provides health and occupational safety information for this product. Most foils are produced from cast ingots for use in coating and thin film Chemical Vapor Deposition (CVD) and Physical Vapor Deposition (PVD) processes including Thermal and Electron Beam (E-Beam) Evaporation, Low Temperature Organic Evaporation, Atomic Layer Deposition (ALD), Organometallic and Chemical Vapor Deposition (MOCVD) for specific applications such as fuel cells and solar energy. Thickness can range from 0.003" to approximately 2mm for all metals. Some metals can also be rolled down as thin as 0.001" for use as an evaporation source in microelectronics, optics, magnetics, MEMS, and hard resistant coatings. Piece sizes are available up to approximately 7" maximum width. Maximum lengths of about 20" can be obtained with a nominal thickness between about 0.005" and 0.020" for thin film deposition on glass or metal substrates. Materials are produced using crystallization, solid state and other ultra high purification processes such as sublimation. American Elements specializes in producing custom compositions for commercial and research applications and for new proprietary technologies. American Elements also casts any of the rare earth metals and most other advanced materials into rod, bar, or plate form, as well as other machined shapes and through other processes such as nanoparticles and in the form of solutions and organometallics. We also produce Lead as rods, powder and plates. Other shapes are available by request.

Approx. 550 / Kg Get Latest Price

Lead Anode is used as an electrode during Zinc Refining / Electrolysis. The company has brought commercial production of Lead Anode made by Lead-Silver Alloy or as per desired specification made the customers. Lead Anode, One of the major uses is in zinc smelters to do protection against corrosion as it is also anodic in behavior to noble metals.

Approx. 300 / Kg Get Latest Price

Lead Balls is small balls of Lead, traditionally made using a shot tower. It is used for a variety of purposes. One use of shot is in shotguns. Lead Balls has been used to provide variable weight in stress testing systems. Shot pours from a hopper into a basket, which is connected to the test item. When the test item

Approx. 250 / Kg Get Latest Price

In printing, type metal refers to the metal alloys used in traditional typefounding and hot metal typesetting. Historically, type metal was an alloy of lead, tin and antimony in different proportions depending on the application, be it individual character mechanical casting for hand setting, mechanical line casting or individual character mechanical typesetting and stereo plate casting. The proportions used are in the range: lead 5086%, antimony 1130% and tin 320%. Antimony and tin are added to lead for durability while reducing the difference between the coefficients of expansion of the matrix and the alloy. Apart from durability, the general requirements for type-metal are that it should produce a true and sharp cast, and retain correct dimensions and form after cooling down. It should also be easy to cast, at reasonable low melting temperature, iron should not dissolve in the molten metal, and mould and nozzles should stay clean and easy to maintain. Today, Monotype machines can utilize a wide range of different alloys. Mechanical linecasting equipment uses alloys that are close to eutectic.Type metal compositions

Approx. 350 / Kg Get Latest Price

The lead pipe is the length of pipe on which a jacking shield is mounted during a horizontal directional drilling operation. The shield is placed over the end of the lead pipe to protect workers during the excavation process. The lead pipe is specifically manufactured with a flat end instead of a spigot and it does not have joint gaskets.

Approx. 230 / Kg Get Latest Price

Lead Wool is low density permeable material with numerous applications. The defining characteristic of these wools is a very high porosity, typically 75-95% of the volume consisting of void spaces. Metallic wools have found a wide variety of applications in heat exchangers, energy absorption, flow diffusion and lightweight optics.Appearance: Bluish whiteBoiling Point: 1740 °CMelting Point: 327.502 °CMolecular Weight: 207.2