Fine Metal (India)

Established in the Year 1988 in Mumbai, Maharashtra. We "Fine Metal India" are Partnership Firm, engaged as the foremost Wholesale Trader of Metal Ingots, Solder Stick & Solder Wire.

 solder wire 60/40 (Sn/Pb) has good solderability, insulation resistance, No spattering, and is non-corrosive. Its composition is 60/40 of Tin (Sn) and Lead (Pb) respectively.  Noel Solder wire is widely used in electrical and electronics, solder parts like a circuit board, electronics devices, and others.

Rosin Mildly Activated (RMA) / No Clean (NC) can be used for General Purpose Soldering in Electrical & Electronics industries.

Pack Size - 10gm, 40gm, 50gm, 100gm, 250gm, 500gm

SWG - 20/22

Flux content - 1.2%-2%

Features: 60/40 solder       

• Instant Wetting Behaviour
• High mobility, fast-spreading action of this flux result in more reliable Production line Soldering.
• Rosin Core Solder
• Minimum Resistance
• Excellent manufacturing consistency and uniform quality
• No Additional Flux or paste is required
• No Dry Solder
• Creates Less smoke and Odour
• Low Melting Point
• Clear residue, resulting in excellent Joint Aesthetics after Soldering.

 solder wire 60/40 is useful for all electronic general-purpose.

 

 solder wire 60/40 contain an optimum balance of Rosin and Activators. The alloys used for Multicore Solder wire conform to the purity requirements of the common national and international standards.

 A wide range of wire diameters are manufactured to close dimensional tolerances. These start from SWG 12, 14, 16, 18, 20, 21, 22 and 24.

 

An optimum Temperature and controlled heating is required while doing efficient soldering. Excess Heating should be avoided while using 60/40 Solder wire.

 

Pack Sizes: 10gm, 40gm, 50gm, 100gm, 250gm, 500gm

Cleaning:

Solder wire 60/40 cored Solder wires have been formulated in such a way that very bare minimum flux residue comes while soldering. In most of the electronic, and electrical applications, cleaning will not be required. Hence, 60/40 Solder wire may therefore be used to compliment a NO- CLEAN Soldering or Reflow process or to allow repairs without need for a second cleaning process.

 

solder wire 63/37(Sn/Pb) has good solderability, insulation resistance, No spattering, and is non-corrosive. Its composition is 63/37 of Tin (Sn) and Lead (Pb) respectively.  Noel Solder wire is widely used in electrical and electronics, solder parts like a circuit board, electronics devices, and others.

Rosin Mildly Activated (RMA) / No Clean (NC) Solder Wire can be used for General Purpose Soldering in Electrical & Electronics industries.

Pack Size - 50gm, 100gm, 250gm, 500gm

SWG - 20/22

Flux content - 1.2%-2%

Features:         

• Instant Wetting Behaviour
• High mobility, fast-spreading action of this Flux results in more reliable Production line Soldering.
• Rosin Core Solder
• Minimum Resistance
• Excellent manufacturing consistency and uniform quality
• No Additional Flux or paste is required
• No Dry Solder
• Creates Less smoke and Odour
• Low Melting Point
• Clear residue, resulting in excellent Joint Aesthetics after Soldering.

 

 solder wire 50/50 (Sn/Pb) has good solderability, insulation resistance, No spattering, and is non-corrosive. Its composition is 50/50 of Tin (Sn) and Lead (Pb) respectively.   Solder wire is widely used in electrical and electronics, solder parts like a circuit board, electronics devices, and others.

RMA or Flux Core Solder Wire can be used for General Purpose Soldering in the Electrical & Electronics industries.

Pack Size - 10gm, 40gm, 50gm, 100gm, 250gm, 500gm

SWG - 20/22

Features:         

• Instant Wetting Behaviour
• High mobility, fast-spreading action of this Flux results in more reliable Production line Soldering.
• Rosin Core Solder
• Minimum Resistance
• Excellent manufacturing consistency and uniform quality
• No Additional Flux or paste is required
• No Dry Solder
• Creates Less smoke and Odour
• Low Melting Point
• Clear residue, resulting in excellent Joint Aesthetics after Soldering.

 

AAC Solder Wire are soft soldering wire that contains lead is comprised of combinations of tin, lead, silver, cadmium and copper. Combinations of tin and lead are in ratios of 30 percent tin/70 percent lead. These solders melt in a range from 421 to 561 degrees with the higher the percentage of lead, the higher the melting point. 

• The main constituents of 20/80 solder wire are Tin (Sn) and Lead (Pb). • Solder wire is made high of uniquely labelled of rosin and proprietary activators which provides rapid wetting and good spreadability. The wire is made from virgin Tin/Lead having 99.9% purity. • Health and Safety: It is not toxic however a certain amount of fumes will be generated; therefore these fumes must be exhausted for the operator’s safety. • First Aid Measures: EYE CONTACT: i) Flush eye immediately with plenty of running water for 15 minutes, including under eyelids, ii) Contact Doctor. SKIN CONTACT: i) Wash with soap and water, ii) If you feel irritation on the skin, contact Doctor. INHALATION: i) Move the patient to a fresh air environment, ii) Contact Doctor. INGESTION: i) Drink plenty of water, ii) Contact Doctor. • Melting temperature range and specific gravity of solder alloy: Melting temperature range ºC - 183-280. Specific gravity - 10.20. • PHYSICAL PROPERTIES: Item --> Solder Wire- (Sn20/Pb80) Appearance --> Bright shinning. Melting point (ºC) --> 183-280. Specific gravity (gm/cm3) --> 10.2 Tensile strength (MPa/min.) --> 47. Recommended operation temperature of soldering --> 375 -425ºC • TECHNICAL SPECIFICATION Physical Properties--> Typical Value Rosin Grade --> WW per Fed, Spec LLL-R-626 Water Extract Resistively --> 40.000 ohm-cm , typical Corrosion test --> Passes. J-STD-004 IPC-SF-818 Spreadability --> More Than 85%. Electromigration --> Passed. S.I.R. --> Passed.

 Solder Wire 5/95 

Tin Lead Solder Wire 5/95 is known as solder wire Sn5Pb95, it is a low tin soft solder wire made of 5% tin and 95% of lead. XF Solder wire is furnished with a rosin flux at nominal 2.0% which is evenly distributed inside the wire as a single core, during using there's no need apply external flux. Solder wire 5/95 is a high melting point solder because of the higher percentage of lead making the alloy more heat resistant The appearance of Solder wire 5/95 (Sn5Pb95) looks dull, not as silvery color as the high tin alloy. And the solder joint solidified more quickly than the high tin solder wire. 

The GI wire or Galvanized Iron Wire is a result of a process called Galvanization. An anti-rust shielded zinc metal coating makes the wire rust-resistant.

Established in the Year 1988 in Mumbai, Maharashtra. We "Fine Metal India" are Partnership Firm, engaged as the foremost Wholesale Trader of Metal Ingots, Solder Stick & Solder Wire.

 solder wire 40/60 (Sn/Pb) has good solderability, insulation resistance, No spattering, and is non-corrosive. Its composition is 40/60 of Tin (Sn) and Lead (Pb) respectively.   Solder wire is widely used in electrical and electronics, solder parts like a circuit board, electronics devices, and others.

RMA or Flux Core Solder Wire can be used for General Purpose Soldering in the Electrical & Electronics industries.

Pack Sizes - 10gm, 40gm, 50gm, 100gm, 250gm, 500gm

SWG - 20/22

Features:             

1. Instant Wetting Behavior
2. High mobility, fast-spreading action of this Flux results in more reliable Production line Soldering.
3. Rosin Core Solder
4. Minimum Resistance
5. No Additional Flux or paste is required
6. No Dry Solder
7. Low Melting Point
8. Widely applied in Repairs works
9. Creates less smoke and odor
10. Excellent manufacturing consistency and uniform quality.

Tin Lead Solder Wire 10/90 is known as solder wire Sn10Pb90, it is made of 10% tin and 90% of lead. This is a low tin solder wire with very affordable cost. XF Solder wire is furnished with a rosin flux at nominal 2.0% which is evenly distributed inside the wire as a single core, during using there's no need apply external flux. Solder wire 10/90 is a high melting point solder because of the higher percentage of lead making the alloy more heat resistant The appearance of Solder wire 10/90 (Sn10Pb90) looks dull, not as silvery color as the high tin alloy.